Touch-Less Snow Foam - 5000ml
49,99
- Zeer effectieve prewash foam
- Geschikt voor foamlans, handfoamers en zelfs sprayers
- Biologisch afbreekbaar
- Gemiddelde PIR van 1%
- Ordered before 9:00 PM, shipped the same business day!
- Free shipping on orders from €50!
- Premium delivery options with PostNL
- Easy payment: PayPal, Credit Card and iDEAL
- Pay later for free with Klarna
49,99
With an average PIR (Panel Impact Ratio) of 0.5 - 2%, this sugar-based biodegradable formula is highly effective in contactless cleaning of car paint. Unlike other petroleum-based cleaners, Touch-Less is very easy to rinse off without leaving any residue, making bucket washing afterward simpler and faster. Additionally, Touch-Less contains corrosion inhibitors. It is free from phosphates, solvents, NTA, and caustic soda.
Product number: | BH-TOUCHLESS-5000 |
---|
The minimum recommended PIR (Panel Impact Ratio) is 0.5%, up to a maximum of 2% for very dirty vehicles. The dilution in a hand foamer or spray bottle is easy to determine. For foam lances, it is more challenging because it depends on the water flow rate of the pressure washer.
The following steps need to be done only once; don’t forget to note the ratio on the packaging for future use.
- Fill the mixing bottle with tap water to the maximum level. Set the foam lance, or if you’re using the pressure washer’s reservoir, to the maximum product flow.
- Take an empty large bucket and spray with the foam lance connected into the bucket until the entire mixing bottle is empty and stop immediately. If the bottle is not empty and the bucket is full, halve the amount of water in the mixing bottle and start again. All the following numbers should then also be halved.
- The following calculation provides a PIR of 2%. Measure the total amount of liters in the bucket after the mixing bottle is empty. Multiply this number by 0.02.
- The resulting number is the amount of product needed for the content of your mixing bottle.
- Mix the bottle with the desired amount of product and water.
- Foam the car and let it dwell for 1-5 minutes. Never let the product dry. Then rinse off with high pressure.
- Fill the mixing bottle completely with tap water (1000 ml).
- Attach the foam lance to the pressure washer and turn the knob on top fully closed (maximum foam setting).
- Spray into an empty large bucket until the 1000 ml mixing bottle is (almost) empty.
- Once the bottle is almost empty, the bucket is filled with 13 liters of water.
- The amount of product needed is 13 x 0.02 = 260 ml, and the rest with water.
- You do not need to use all the mixture at once; the mixture can be stored. You can also use half by mixing 130 ml of product with 240 ml of water. With one liter of mixture, you can do about 8-10 washes, depending on your pressure washer and water pressure.
1 - 3 of 28 reviews
WOW...alle verwachtingen overtroffen
1e keer gebruik...niet tevreden...wat bleek Hogedruk kapot. Daarna de handspray aangeschaft (met pomp nippel) en met de juiste dosering naar de wasbox. inspraken (extra aangemaakt materiaal voor in de spray te stoppen mee) in laten trekken, afspuiten met hoge druk en daarna vlekvrij naspoelen (daarom de wasbox) en de auto ziet er zeer schoon uit. Nee beslist geen hadnschoen-was-effect maar voor de winter ideaal om elke week even die smerige pekel van je auto af te halen. En trouwens ook super voor het schoonmaken van de motor :)
Goed
Eerste keer gebruikt en blijft zeker in mij assortiment Gewoon gebruikt met een handsprayer ook heel goed te doen
Topproduct!
Na veel video’s te bekeken te hebben, besloten om deze te proberen en moet eerlijk toegeven ben enorm verrast van het resultaat. Werkt wel beter vanaf 1,5 tot 2 PIR zeker niet lager gaan. Niet goedkoop maar wel doeltreffend bij zeer vervuilde wagens. Had al enkele andere merken geprobeerd maar deze is voor mij een blijver 👍