Touch-Less Snow Foam - 1000ml | 1000ml

Bilthamber Touch-Less is the new eco-friendly pre-wash suitable for foam lances and hand foamers. You can even use the product in a spray bottle or pump dispenser.

With an average PIR (Panel Impact Ratio) of 0.5 - 2%, this sugar-based biodegradable formula is highly effective in contactless cleaning of car paint. Unlike other petroleum-based cleaners, Touch-Less is very easy to rinse off without leaving any residue, making bucket washing afterward simpler and faster. Additionally, Touch-Less contains corrosion inhibitors. It is free from phosphates, solvents, NTA, and caustic soda.

Product number:	BH-TOUCHLESS1L

H318: Causes serious eye damage.

Touch-Less can be applied using a foam lance, hand foamer, or spray bottle.

The minimum recommended PIR (Panel Impact Ratio) is 0.5%, up to a maximum of 2% for very dirty vehicles. The dilution in a hand foamer or spray bottle is easy to determine. For foam lances, it is more challenging because it depends on the water flow rate of the pressure washer.

The following steps need to be done only once; don’t forget to note the ratio on the packaging for future use.

Fill the mixing bottle with tap water to the maximum level. Set the foam lance, or if you’re using the pressure washer’s reservoir, to the maximum product flow.
Take an empty large bucket and spray with the foam lance connected into the bucket until the entire mixing bottle is empty and stop immediately. If the bottle is not empty and the bucket is full, halve the amount of water in the mixing bottle and start again. All the following numbers should then also be halved.
The following calculation provides a PIR of 2%. Measure the total amount of liters in the bucket after the mixing bottle is empty. Multiply this number by 0.02.
The resulting number is the amount of product needed for the content of your mixing bottle.
Mix the bottle with the desired amount of product and water.
Foam the car and let it dwell for 1-5 minutes. Never let the product dry. Then rinse off with high pressure.

Example Calculation with a Pressure Washer and a Monello Lancia Foam Lance with a 1000 ml Mixing Bottle:

Fill the mixing bottle completely with tap water (1000 ml).
Attach the foam lance to the pressure washer and turn the knob on top fully closed (maximum foam setting).
Spray into an empty large bucket until the 1000 ml mixing bottle is (almost) empty.
Once the bottle is almost empty, the bucket is filled with 13 liters of water.
The amount of product needed is 13 x 0.02 = 260 ml, and the rest with water.
You do not need to use all the mixture at once; the mixture can be stored. You can also use half by mixing 130 ml of product with 240 ml of water. With one liter of mixture, you can do about 8-10 washes, depending on your pressure washer and water pressure.

Downloads

Veiligheidsblad Touch-Less (ENG)

Videos

3 of 27 reviews

Write a review

Share your experience and help others choose!

Log in

Your email address

Your password

Sort by

19 April 2022 17:29

Top foam

Dit is veruit de beste foam die nu verkrijgbaar is volgens mij, m’n auto inschuimen, 5 minuten wachten en van onder naar boven met de hoge druk. Zo goed als een gewassen wagen.

27 January 2022 17:28

beste prewash tot nu toe

Tot nu toe de beste prewash die ik heb gebruikt. Lost heel veel vervuiling op en komt verdraaid dicht tegen een echte touchless wash. Voor een spiegelglans zul je altijd wel nog een contactwash moeten doen, maar voor een snelle beurt met toch een heel deftig resultaat is dit het product. En hoe nauwkeuriger je daarna met de hogedruk afspoelt, hoe vlekkeloze het resultaat. Ik bracht het aan met foamlance en hogedruk met ca 50 ml op een formules van 500 ml. PIR dus nog niet gevolgd. Geeft een melkachtige laag die zijn werk goed doet. Geen showtoestanden met hopen schuim die je uren daarna nog op de oprit vindt (naar mijn verlangen hé, dus als je scheerschuim wil dan denk ik dat dit niet je product is...). Het doet heel goed wat ik ervan verwacht.

27 December 2021 20:23